Description
EIGRP Interview Questions & Answers Vol 1.0
Questions 80
Check the complete list of questions:
- Does EIGRP require “ip default-network” command to propagate a default route?
- Should I always use the eigrp log-neighbor-changes command when I configure EIGRP?
- Does EIGRP support secondary addresses?
- What debugging capabilities does EIGRP have?
- Do EIGRP support aggregation and variable-length subnet masks?
- Can I configure more than one EIGRP autonomous system on the same router?
- If there are two EIGRP processes that run and two equal paths are learned, one by each EIGRP process, do both routes get installed?
- What does the neighbor statement in the EIGRP configuration section do?
- What does the word serno mean on the end of an EIGRP topology entry when you issue the show ip eigrp topology command?
- What percent of bandwidth and processor resources does EIGRP use?
- Does EIGRP support areas?
- What does the EIGRP stuck in an active message mean?
- Why does the EIGRP passive-interface command remove all neighbors for an interface?
- Why are routes received from one neighbor on a point-to-multipoint interface that runs EIGRP not propagated to another neighbor on the same point-to-multipoint interface?
- When I configure EIGRP, how can I configure a network statement with a mask?
- I have two routes: 192.168.1.0/24 and 192.168.1.0/28. How can I deny 192.168.1.0/28 while I allow 192.168.1.0/24 in EIGRP?
- I have a router that runs CEF and EIGRP. Who does load-balancing when there are multiple links to a destination?
- How do you verify if the EIGRP Non-Stop Forwarding (NSF) feature is enabled?
- How can I use only one path when a router has two equal-cost paths?
- What is the difference in metric calculation between EIGRP and IGRP?
- What is the EIGRP Stub Routing feature?
- How can I send a default route to the Stub router from the hub?
- What are different route types in EIGRP?
- How do you redistribute an IPv6 default route in EIGRP?
- How does EIGRP behave over a GRE tunnel compared to a directly connected network?
- What is an offset-list, and how is it useful?
- How can I tag external routes in EIGRP?
- What are the primary functions of the PDM?
- What are the various load-balancing options available in EIGRP?
- What does the %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 10.152.0.5 (Tunnel0) is down: holding time expired error message mean?
- Is there an IPv6 deployment guide that includes EIGRPv6?
- From the 16:29:14.262 Poison squashed: 10.X.X.X/24 reverse message, what does poison squashed mean?
- Is it normal that EIGRP takes over 30 seconds to converge?
- Which command will display all the EIGRP feasible successor routes known to a router?
- Which EIGRP information is held in RAM and maintained through the use of Hello and update packets?
- EIGRP uses which Protocol and AD?
- For EIGRP neighborship to form what are requirements?
- What is Active & Passive State in EIGRP?
- Which commands are used for implementing EIGRP on Cisco Router?
- What are the EIGRP Tables?
- What is EIGRP summary route and EIGRP external route?
- How to turn on classless routing in EIGRP?
- What are the different types of EIGRP packets?
- How two EIGRP router become neighbors with each other?
- What is Advertised Distance, Feasible-Distance, Successor route, Feasible Successor route in EIGRP?
- Which algorithm does EIGRP use for finding the best path?
- What is the Hello, Hold timers in EIGRP?
- Why variance command is used in EIGRP?
- What is “Stuck in Active” condition in EIGRP?
- What are the methods of summarization in EIGRP?
- What are the different tables in EIGRP?
- Why EIGRP is called hybrid protocol?
- What are the values of internal and external routes in EIGRP?
- What type of authentication is supported by EIGRP?
- What are the advantages of EIGRP over other protocols?
- What is the multicast address used by EIGRP to send hello packets?
- What is “Graceful Shutdown” in EIGRP?
- What is the “Goodbye” message in EIGRP?
- What is the maximum no of paths load-balanced by EIGRP?
- What is a passive interface in EIGRP?
- What are the different K-values used in EIGRP?
- What do you mean by backward compatibility of IGRP with EIGRP? Do we need to do redistribution between IGRP and EIGRP? Explain either case
- What is the formula of metric calculation of EIGRP? What is the K value?
- What is the Hello, Hold timers in EIGRP?
- What do you mean by PDM (Protocol Dependency Module)? Does EIGRP support IPv6?
- What are the commands we use to check eigrp neighborship and eigrp topology table?
- How can we check routes in the topology table that don’t meet feasible condition?
- What is the max hop limit in eigrp?
- What’s the default hop limit in EIGRP?
- How many paths can be load balanced in eigrp?
- What is the default limit of paths that can be load balanced in EIGRP?
- What are the 4 basic components of EIGRP?
- What is RTP in EIGRP?
- What packets in EIGRP is RTP enabled?
- Will 2 EIGRP Routers with the same Router id form neighborship?
- What is the downside of 2 EIGRP neighbors with same Router ID?
- What is the Split horizon?
- Does EIGRP support secondary addresses?
- What is the difference in metric calculation between EIGRP and IGRP?
- How to configure summarization on the specific interface in EIGRP?
Reviews
There are no reviews yet.